Hello,
I am trying to transmit and receive using 2 different supported boards (2x ZEDBOARD + 2x FMCOMMS3) using following example:
https://in.mathworks.com/help/soc/ug/hw-sw-co-design-qpsk-transmit-and-receive-using-analog-devices-ad9361-ad9364.html
I have succesfully compiled the simulation, programmed the board via HDL Coder and HDL Workflow Advisor and transmitted and received with ease using one board. However, when trying to use 2 boards, I do not know the procedure I need to follow for a successful TX/RX over air. I am not able to see the other board’s data at the receiver. I do not receive anything.
My approach was the following:
– I configured both ZEDBOARDs with the bitstream of the example.
– I attached one antenna to the TX port of the TX FMCOMMS3 and one antenna to the RX port of the RX FMCOMMS3.
– I disabled on one end the AD936x transmitter system and on the other the AD936x receiver system.
– The systems can be seen in the attached images.
– The UDP receive model was running on the receiver side.
The result: I do not see any bits coming into the RX side.

Anybody has some expertise in this? Maybe there are other examples which I have not discovered yet that address this scenario…
Any help would be welcome. Thank you in advance

—————————————————————————————-
RX Side:

TX side:

UDP Model:Hello,
I am trying to transmit and receive using 2 different supported boards (2x ZEDBOARD + 2x FMCOMMS3) using following example:
https://in.mathworks.com/help/soc/ug/hw-sw-co-design-qpsk-transmit-and-receive-using-analog-devices-ad9361-ad9364.html
I have succesfully compiled the simulation, programmed the board via HDL Coder and HDL Workflow Advisor and transmitted and received with ease using one board. However, when trying to use 2 boards, I do not know the procedure I need to follow for a successful TX/RX over air. I am not able to see the other board’s data at the receiver. I do not receive anything.
My approach was the following:
– I configured both ZEDBOARDs with the bitstream of the example.
– I attached one antenna to the TX port of the TX FMCOMMS3 and one antenna to the RX port of the RX FMCOMMS3.
– I disabled on one end the AD936x transmitter system and on the other the AD936x receiver system.
– The systems can be seen in the attached images.
– The UDP receive model was running on the receiver side.
The result: I do not see any bits coming into the RX side.

Anybody has some expertise in this? Maybe there are other examples which I have not discovered yet that address this scenario…
Any help would be welcome. Thank you in advance

—————————————————————————————-
RX Side:

TX side:

UDP Model: Hello,
I am trying to transmit and receive using 2 different supported boards (2x ZEDBOARD + 2x FMCOMMS3) using following example:
https://in.mathworks.com/help/soc/ug/hw-sw-co-design-qpsk-transmit-and-receive-using-analog-devices-ad9361-ad9364.html
I have succesfully compiled the simulation, programmed the board via HDL Coder and HDL Workflow Advisor and transmitted and received with ease using one board. However, when trying to use 2 boards, I do not know the procedure I need to follow for a successful TX/RX over air. I am not able to see the other board’s data at the receiver. I do not receive anything.
My approach was the following:
– I configured both ZEDBOARDs with the bitstream of the example.
– I attached one antenna to the TX port of the TX FMCOMMS3 and one antenna to the RX port of the RX FMCOMMS3.
– I disabled on one end the AD936x transmitter system and on the other the AD936x receiver system.
– The systems can be seen in the attached images.
– The UDP receive model was running on the receiver side.
The result: I do not see any bits coming into the RX side.

Anybody has some expertise in this? Maybe there are other examples which I have not discovered yet that address this scenario…
Any help would be welcome. Thank you in advance

—————————————————————————————-
RX Side:

TX side:

UDP Model: simulink, ad9361, zedboard, fmcomms3 MATLAB Answers — New Questions

​