I am currently working with a MathWorks reference example and we were able to run this example on the ZCU208 evaluation board, and it works correctly on that platform.

However, we now need to run the same example on our custom hardware board, which is based on a Zynq UltraScale+ RFSOC (ZU48DR) device.

We would like to understand whether it is possible to port the ZCU208 reference design to a custom ZU48DR-based board.

We attempted to create a custom board using the workflow described in the MathWorks documentation:
https://in.mathworks.com/help/soc/ug/create-board-support-framework.html
However, at the very first step, MATLAB reports that there is no available RFSOC board support. It says Only the following boards are supported – Zynq-7000 SoC and Zynq UltraScale+ MPSoC. There is no option available for Zynq UltraScale+ RFSOC.

Could you please clarify if MATLAB currently provides official support for creating custom RFSoC boards? and Is there a recommended method to port the ZCU208 reference workflow to a custom ZU48DR board?

Additionally, we observed that when running the workflow on a ZCU111 board, the rftool configures the clocks(for CLK 104 board) and initializes the RFDC IP.

Is it possible for us to gain access to or enable rftool functionality when using custom RFSOC board?I am currently working with a MathWorks reference example and we were able to run this example on the ZCU208 evaluation board, and it works correctly on that platform.

However, we now need to run the same example on our custom hardware board, which is based on a Zynq UltraScale+ RFSOC (ZU48DR) device.

We would like to understand whether it is possible to port the ZCU208 reference design to a custom ZU48DR-based board.

We attempted to create a custom board using the workflow described in the MathWorks documentation:
https://in.mathworks.com/help/soc/ug/create-board-support-framework.html
However, at the very first step, MATLAB reports that there is no available RFSOC board support. It says Only the following boards are supported – Zynq-7000 SoC and Zynq UltraScale+ MPSoC. There is no option available for Zynq UltraScale+ RFSOC.

Could you please clarify if MATLAB currently provides official support for creating custom RFSoC boards? and Is there a recommended method to port the ZCU208 reference workflow to a custom ZU48DR board?

Additionally, we observed that when running the workflow on a ZCU111 board, the rftool configures the clocks(for CLK 104 board) and initializes the RFDC IP.

Is it possible for us to gain access to or enable rftool functionality when using custom RFSOC board? I am currently working with a MathWorks reference example and we were able to run this example on the ZCU208 evaluation board, and it works correctly on that platform.

However, we now need to run the same example on our custom hardware board, which is based on a Zynq UltraScale+ RFSOC (ZU48DR) device.

We would like to understand whether it is possible to port the ZCU208 reference design to a custom ZU48DR-based board.

We attempted to create a custom board using the workflow described in the MathWorks documentation:
https://in.mathworks.com/help/soc/ug/create-board-support-framework.html
However, at the very first step, MATLAB reports that there is no available RFSOC board support. It says Only the following boards are supported – Zynq-7000 SoC and Zynq UltraScale+ MPSoC. There is no option available for Zynq UltraScale+ RFSOC.

Could you please clarify if MATLAB currently provides official support for creating custom RFSoC boards? and Is there a recommended method to port the ZCU208 reference workflow to a custom ZU48DR board?

Additionally, we observed that when running the workflow on a ZCU111 board, the rftool configures the clocks(for CLK 104 board) and initializes the RFDC IP.

Is it possible for us to gain access to or enable rftool functionality when using custom RFSOC board? custom zu48dr-based board MATLAB Answers — New Questions

​