The measurement error that occurred previously is no longer happening.
If no input is provided to the Scenario Reader, no errors occur.
However, when I start providing values through parkEgo in the Scenario, the ultrasonicDetectionGenerator fails to produce any output and continuously encounters errors.
The simulation does not terminate due to the error, but it remains stuck without producing any output, and when I press ctrl+c in the Matlab command window, it always shows an error in the Implement of ultrasonicDetectionGenerator.
https://kr.mathworks.com/matlabcentral/answers/2137952-measurement-error-of-ultrasonic-sensor-in-driving-scenario-designer/?s_tid=ans_lp_feed_leaf
Due to the above issue, I am currently using the prerelease version 2024b.

시뮬레이션 중에 오류가 발생하여 시뮬레이션이 종료되었습니다
원인:
‘ultrasonicDetectionGenerator’의 ‘stepImpl’ 메서드를 호출할 때 MATLAB System 블록 ‘AIV_robot/Environment/Simulation/Ultrasonic Sensor Processing/Ultrasonic5’에서 오류가 발생했습니다.
프로그램 중단(Ctrl+C)이 감지되었습니다.
An error occurred during the simulation, causing it to terminate.
Cause:
An error occurred in the MATLAB System block ‘AIV_robot/Environment/Simulation/Ultrasonic Sensor Processing/Ultrasonic5’ while calling the ‘stepImpl’ method of ‘ultrasonicDetectionGenerator’.
Program interruption (Ctrl+C) was detected.The measurement error that occurred previously is no longer happening.
If no input is provided to the Scenario Reader, no errors occur.
However, when I start providing values through parkEgo in the Scenario, the ultrasonicDetectionGenerator fails to produce any output and continuously encounters errors.
The simulation does not terminate due to the error, but it remains stuck without producing any output, and when I press ctrl+c in the Matlab command window, it always shows an error in the Implement of ultrasonicDetectionGenerator.
https://kr.mathworks.com/matlabcentral/answers/2137952-measurement-error-of-ultrasonic-sensor-in-driving-scenario-designer/?s_tid=ans_lp_feed_leaf
Due to the above issue, I am currently using the prerelease version 2024b.

시뮬레이션 중에 오류가 발생하여 시뮬레이션이 종료되었습니다
원인:
‘ultrasonicDetectionGenerator’의 ‘stepImpl’ 메서드를 호출할 때 MATLAB System 블록 ‘AIV_robot/Environment/Simulation/Ultrasonic Sensor Processing/Ultrasonic5’에서 오류가 발생했습니다.
프로그램 중단(Ctrl+C)이 감지되었습니다.
An error occurred during the simulation, causing it to terminate.
Cause:
An error occurred in the MATLAB System block ‘AIV_robot/Environment/Simulation/Ultrasonic Sensor Processing/Ultrasonic5’ while calling the ‘stepImpl’ method of ‘ultrasonicDetectionGenerator’.
Program interruption (Ctrl+C) was detected. The measurement error that occurred previously is no longer happening.
If no input is provided to the Scenario Reader, no errors occur.
However, when I start providing values through parkEgo in the Scenario, the ultrasonicDetectionGenerator fails to produce any output and continuously encounters errors.
The simulation does not terminate due to the error, but it remains stuck without producing any output, and when I press ctrl+c in the Matlab command window, it always shows an error in the Implement of ultrasonicDetectionGenerator.
https://kr.mathworks.com/matlabcentral/answers/2137952-measurement-error-of-ultrasonic-sensor-in-driving-scenario-designer/?s_tid=ans_lp_feed_leaf
Due to the above issue, I am currently using the prerelease version 2024b.

시뮬레이션 중에 오류가 발생하여 시뮬레이션이 종료되었습니다
원인:
‘ultrasonicDetectionGenerator’의 ‘stepImpl’ 메서드를 호출할 때 MATLAB System 블록 ‘AIV_robot/Environment/Simulation/Ultrasonic Sensor Processing/Ultrasonic5’에서 오류가 발생했습니다.
프로그램 중단(Ctrl+C)이 감지되었습니다.
An error occurred during the simulation, causing it to terminate.
Cause:
An error occurred in the MATLAB System block ‘AIV_robot/Environment/Simulation/Ultrasonic Sensor Processing/Ultrasonic5’ while calling the ‘stepImpl’ method of ‘ultrasonicDetectionGenerator’.
Program interruption (Ctrl+C) was detected. driving scenario designer, ultrasonicdetectiongenerator, scenarioreader, simulink, matlab MATLAB Answers — New Questions

​