Category: News
Running code inspector with a For Loop Iterator
Hello,
I have a model running with a For Iterator (to read an Input Array and write some of its datas to another one shorter array).
The model must go through both Model Advisor and Code Inspector to be embedded in the calculator.
As for the Model Advisor everything is passed and generated code is about 120 lines, however when I try to run the code inspector, it runs for more than 2.5hrs (on the inspection only) and I am forced to kill the Matlab task afterward because it stops running. Here is a screenshot of the model.
Here is what I tried:
include the "add" and the "unitDelaty" inside the referenced model => it creates an algebraic loop
add the triggered block within a referenced model => impossible as it contain an "assignement" block and therefore cannot be referenced.
Simplify the referenced model to reduce load capacity of the model containg.
I can provide the generated C code if necessary
Thank you,Hello,
I have a model running with a For Iterator (to read an Input Array and write some of its datas to another one shorter array).
The model must go through both Model Advisor and Code Inspector to be embedded in the calculator.
As for the Model Advisor everything is passed and generated code is about 120 lines, however when I try to run the code inspector, it runs for more than 2.5hrs (on the inspection only) and I am forced to kill the Matlab task afterward because it stops running. Here is a screenshot of the model.
Here is what I tried:
include the "add" and the "unitDelaty" inside the referenced model => it creates an algebraic loop
add the triggered block within a referenced model => impossible as it contain an "assignement" block and therefore cannot be referenced.
Simplify the referenced model to reduce load capacity of the model containg.
I can provide the generated C code if necessary
Thank you, Hello,
I have a model running with a For Iterator (to read an Input Array and write some of its datas to another one shorter array).
The model must go through both Model Advisor and Code Inspector to be embedded in the calculator.
As for the Model Advisor everything is passed and generated code is about 120 lines, however when I try to run the code inspector, it runs for more than 2.5hrs (on the inspection only) and I am forced to kill the Matlab task afterward because it stops running. Here is a screenshot of the model.
Here is what I tried:
include the "add" and the "unitDelaty" inside the referenced model => it creates an algebraic loop
add the triggered block within a referenced model => impossible as it contain an "assignement" block and therefore cannot be referenced.
Simplify the referenced model to reduce load capacity of the model containg.
I can provide the generated C code if necessary
Thank you, simulink, code generation, code inspector MATLAB Answers — New Questions
Regarding file system error on Windows 10
I’ve been experiencing a strange issue with my Windows 10 system where I’m getting frequent file system errors. The error message usually appears when I’m trying to access or move files, and it says that the file system has encountered an error and is unable to complete the requested action. The error message also mentions a specific file or folder, but it’s always a random one. Sometimes the error is resolved by restarting the system or closing the application, but other times it persists and I’m unable to access the affected files or folders. Has anyone else experienced similar issues with their Windows 10 system, and if so, how did they resolve it?
I’ve been experiencing a strange issue with my Windows 10 system where I’m getting frequent file system errors. The error message usually appears when I’m trying to access or move files, and it says that the file system has encountered an error and is unable to complete the requested action. The error message also mentions a specific file or folder, but it’s always a random one. Sometimes the error is resolved by restarting the system or closing the application, but other times it persists and I’m unable to access the affected files or folders. Has anyone else experienced similar issues with their Windows 10 system, and if so, how did they resolve it? Read More
How to access shared subcalendars in Outlook new?
We use several shared calendarfolders for sharing information. These folders reside as subfolders of an account and are shared with everyone in the company. The users can access the folders perfectly in the old outlook desktop version, but this is not possible in the new version. Or is it possible that it’s only me that hasn’t figured out how? Does anybody know?
We use several shared calendarfolders for sharing information. These folders reside as subfolders of an account and are shared with everyone in the company. The users can access the folders perfectly in the old outlook desktop version, but this is not possible in the new version. Or is it possible that it’s only me that hasn’t figured out how? Does anybody know? Read More
I’m unable to login to https://dynamicspartners.transform.microsoft.com/
Hi,
I’m unable to login to https://dynamicspartners.transform.microsoft.com/. Nothing happens when I try to press the login button on the upper right corner.
Result has been the same with three different browsers (Firefox, Chrome & Edge) and with two different PCs.
Our IT says that I have the same rights than my predecessor who used to handle MS incentive cases. I am unable to for example download Proof of Execution documentation f.e: https://dynamicspartners.transform.microsoft.com/download/protected?assetname=protectedassets%2FPartner%20Activities%20-%20Business%20Value%20Assessment%20-%20POE%20Template.pptx&protected=1
Nothing happens when I open that link.
What rights should I have to be able to login to https://dynamicspartners.transform.microsoft.com/?
Any ideas that what could be causing this?
-Ossi
Hi, I’m unable to login to https://dynamicspartners.transform.microsoft.com/. Nothing happens when I try to press the login button on the upper right corner. Result has been the same with three different browsers (Firefox, Chrome & Edge) and with two different PCs. Our IT says that I have the same rights than my predecessor who used to handle MS incentive cases. I am unable to for example download Proof of Execution documentation f.e: https://dynamicspartners.transform.microsoft.com/download/protected?assetname=protectedassets%2FPartner%20Activities%20-%20Business%20Value%20Assessment%20-%20POE%20Template.pptx&protected=1 Nothing happens when I open that link. What rights should I have to be able to login to https://dynamicspartners.transform.microsoft.com/? Any ideas that what could be causing this? -Ossi Read More
Cannot get “$_.hiddenfromaddresslistsenabled -eq $true” to work with other parameters.
Hi Cannot get this command to work. Tried different variations and commands.
Get-Mailbox | Where-Object {$_.IsLicensed -eq $true -and $_.BlockCredential -eq $false -and $_.hiddenfromaddresslistsenabled -eq $true}
The below works fine:
Get-Mailbox | Where-Object {$_.IsLicensed -eq $true -and $_.BlockCredential -eq $false}
Can anyone help?
Hi Cannot get this command to work. Tried different variations and commands. Get-Mailbox | Where-Object {$_.IsLicensed -eq $true -and $_.BlockCredential -eq $false -and $_.hiddenfromaddresslistsenabled -eq $true} The below works fine:Get-Mailbox | Where-Object {$_.IsLicensed -eq $true -and $_.BlockCredential -eq $false} Can anyone help? Read More
Playlist Videos in Sharepoint list shows “Request Access” but i can be played upon clicking it
Hi Team,
We created a playlist and have shared the playlist videos to specific users. However, the playlist shows that they have to request for access. If the select the video, it can be played.
Why the “Request Access” is displayed though access is available. It misleads the user.
Hi Team, We created a playlist and have shared the playlist videos to specific users. However, the playlist shows that they have to request for access. If the select the video, it can be played. Why the “Request Access” is displayed though access is available. It misleads the user. Read More
Understanding SharePoint Online Storage
Understanding SharePoint Online storage used to be easy. Then applications like Loop arrived. Other influences like retention and archive can affect storage too. It’s a complicated situation before you throw OneDrive for Business into the mix and consider that Microsoft has removed unlimited OneDrive storage while an increasing number of apps store files in OneDrive. It’s a complicated situation.
https://office365itpros.com/2024/06/10/sharepoint-online-storage-2/
Understanding SharePoint Online storage used to be easy. Then applications like Loop arrived. Other influences like retention and archive can affect storage too. It’s a complicated situation before you throw OneDrive for Business into the mix and consider that Microsoft has removed unlimited OneDrive storage while an increasing number of apps store files in OneDrive. It’s a complicated situation.
https://office365itpros.com/2024/06/10/sharepoint-online-storage-2/ Read More
The End for Office 365 Connectors Comes Into Sight
Office 365 Connectors bring data from external sources into Microsoft 365 apps like Teams and Outlook. Workflows and Power Automate are replacing Connectors for Microsoft 365 Groups (Outlook groups) and SharePoint Online. Connectors are still available in Teams but for how long? No one knows, but it does seem like Microsoft is rationalizing no-code automation around Power Automate.
https://office365itpros.com/2024/06/11/office-365-connectors-end/
Office 365 Connectors bring data from external sources into Microsoft 365 apps like Teams and Outlook. Workflows and Power Automate are replacing Connectors for Microsoft 365 Groups (Outlook groups) and SharePoint Online. Connectors are still available in Teams but for how long? No one knows, but it does seem like Microsoft is rationalizing no-code automation around Power Automate.
https://office365itpros.com/2024/06/11/office-365-connectors-end/ Read More
Outlook Web based.
Good day!
I am hoping someone can assits me.
My dowloaded Outlook (Left) picks up all my messages but when I log into outlook on the microsoft website (right) it does not pick up any messages?
Good day! I am hoping someone can assits me.My dowloaded Outlook (Left) picks up all my messages but when I log into outlook on the microsoft website (right) it does not pick up any messages? Read More
Save the Date for Global DevOps Experience on June 15!
The Global DevOps Bootcamp, an annual event series that has captured the attention of the DevOps community worldwide by hosting local events to share the latest DevOps and relevant technologies as well as case studies, is being rebranded as the “Global DevOps Experience” (GDEX). This exciting event will take place on Saturday, June 15, 2024.
This event series will feature insights on DevOps, Platform Engineering, and Developer Experience (DevEx), leveraging technologies such as Azure, AI, and GitHub. DevOps communities from around the globe will come together to share their knowledge and experience. Microsoft MVPs and Regional Directors are planning various local events, eagerly anticipating interactions with participants as organizers and speakers.
Visit the event page to learn more about the event story and details of local community events in different countries. Don’t miss out on the opportunity to join an event that interests you.
Microsoft Tech Community – Latest Blogs –Read More
seek demo px4/PX4HITLSimulationFixedWingPlantSimulinkExample
when i use command openExample(‘px4/PX4HITLSimulationFixedWingPlantSimulinkExample’),matlab shows "PX4HITLSimulationFixedWingPlantSimulinkExample" cannot find. So does somebody know how to find this demo? Thanks.when i use command openExample(‘px4/PX4HITLSimulationFixedWingPlantSimulinkExample’),matlab shows "PX4HITLSimulationFixedWingPlantSimulinkExample" cannot find. So does somebody know how to find this demo? Thanks. when i use command openExample(‘px4/PX4HITLSimulationFixedWingPlantSimulinkExample’),matlab shows "PX4HITLSimulationFixedWingPlantSimulinkExample" cannot find. So does somebody know how to find this demo? Thanks. simulationfixedwingplant, simulink, examles MATLAB Answers — New Questions
How do I clean a test file which size stayed big enough?
I’ve got a test file that was linked to larga data files and now those files were reduced in size. Due to the linkage, the test file size was 1.28gb; the fact is that now that the data files were reduced, the test file carries on with the old size and I cannot find a way to "clean it"I’ve got a test file that was linked to larga data files and now those files were reduced in size. Due to the linkage, the test file size was 1.28gb; the fact is that now that the data files were reduced, the test file carries on with the old size and I cannot find a way to "clean it" I’ve got a test file that was linked to larga data files and now those files were reduced in size. Due to the linkage, the test file size was 1.28gb; the fact is that now that the data files were reduced, the test file carries on with the old size and I cannot find a way to "clean it" test file, testing, size MATLAB Answers — New Questions
Need help with FFT of sensor data
Hello.
For my thesis, I am required to analyse one of the five links of 5 DOF robotic arm. The said link has also been designed in solidworks and was imported in Ansys software to find first 4 natural frequencies/mode shapes through Finite Element Analysis (FEA). The natural frequencies are as follows :
0.05934
188.22
476.19
558.74
Ansys also provides the Displacement Time data which can be exported for further analysis. I am currently trying to obtain a magnitude – frequency graph through FFT to find the natural frequencies of the link through exported data.
My understanding is, if I can recreate the natural frequencies given by Ansys through my MATLAB program, I will be able to find acceptable natural frequencies of any link by aquiring acceleration time data through sensors. But in order to do that, I need a program that finds close to accurate natural frequencies through FFT.
I have made/replicated a program, which is attached, by researching online. However, I am obtaining peaks at incorrect frequencies. Furthermore, my plot does not cover all the frequencies on the X-Axis as well.
Summary : I want to make a program that can give me a Magnitude Frequency graph through FFT for a link of a 5 DOF robotic arm. I want to recreate the results comparable or similar to precalculated and correct values of natural frequencies through my program. However, the results through my program are incorrect.
I am sure I must be doing something wrong but I cannot seem to figure it out.
Would appreciate any and all help.
Cheers.
X=readmatrix(‘accl.xlsx’) %importing data
fs=20; % sampling frequency
L=138; % length of signal
nfft=2^nextpow2(L); % next power of 2 from length of freq signal
f=(fs/2)*linspace(0,1,nfft/2+1);
timefft = fft(X(:,2),nfft)/L;% frf of displacement
fre=2*abs(timefft(1:nfft/2+1));% frf of displacement
figure(1),plot(f,fre); grid on % fig A
% Natural frequencies without any scale adjustment
frf=fft(X(:,2));
figure(2),plot((abs(frf))); % fig BHello.
For my thesis, I am required to analyse one of the five links of 5 DOF robotic arm. The said link has also been designed in solidworks and was imported in Ansys software to find first 4 natural frequencies/mode shapes through Finite Element Analysis (FEA). The natural frequencies are as follows :
0.05934
188.22
476.19
558.74
Ansys also provides the Displacement Time data which can be exported for further analysis. I am currently trying to obtain a magnitude – frequency graph through FFT to find the natural frequencies of the link through exported data.
My understanding is, if I can recreate the natural frequencies given by Ansys through my MATLAB program, I will be able to find acceptable natural frequencies of any link by aquiring acceleration time data through sensors. But in order to do that, I need a program that finds close to accurate natural frequencies through FFT.
I have made/replicated a program, which is attached, by researching online. However, I am obtaining peaks at incorrect frequencies. Furthermore, my plot does not cover all the frequencies on the X-Axis as well.
Summary : I want to make a program that can give me a Magnitude Frequency graph through FFT for a link of a 5 DOF robotic arm. I want to recreate the results comparable or similar to precalculated and correct values of natural frequencies through my program. However, the results through my program are incorrect.
I am sure I must be doing something wrong but I cannot seem to figure it out.
Would appreciate any and all help.
Cheers.
X=readmatrix(‘accl.xlsx’) %importing data
fs=20; % sampling frequency
L=138; % length of signal
nfft=2^nextpow2(L); % next power of 2 from length of freq signal
f=(fs/2)*linspace(0,1,nfft/2+1);
timefft = fft(X(:,2),nfft)/L;% frf of displacement
fre=2*abs(timefft(1:nfft/2+1));% frf of displacement
figure(1),plot(f,fre); grid on % fig A
% Natural frequencies without any scale adjustment
frf=fft(X(:,2));
figure(2),plot((abs(frf))); % fig B Hello.
For my thesis, I am required to analyse one of the five links of 5 DOF robotic arm. The said link has also been designed in solidworks and was imported in Ansys software to find first 4 natural frequencies/mode shapes through Finite Element Analysis (FEA). The natural frequencies are as follows :
0.05934
188.22
476.19
558.74
Ansys also provides the Displacement Time data which can be exported for further analysis. I am currently trying to obtain a magnitude – frequency graph through FFT to find the natural frequencies of the link through exported data.
My understanding is, if I can recreate the natural frequencies given by Ansys through my MATLAB program, I will be able to find acceptable natural frequencies of any link by aquiring acceleration time data through sensors. But in order to do that, I need a program that finds close to accurate natural frequencies through FFT.
I have made/replicated a program, which is attached, by researching online. However, I am obtaining peaks at incorrect frequencies. Furthermore, my plot does not cover all the frequencies on the X-Axis as well.
Summary : I want to make a program that can give me a Magnitude Frequency graph through FFT for a link of a 5 DOF robotic arm. I want to recreate the results comparable or similar to precalculated and correct values of natural frequencies through my program. However, the results through my program are incorrect.
I am sure I must be doing something wrong but I cannot seem to figure it out.
Would appreciate any and all help.
Cheers.
X=readmatrix(‘accl.xlsx’) %importing data
fs=20; % sampling frequency
L=138; % length of signal
nfft=2^nextpow2(L); % next power of 2 from length of freq signal
f=(fs/2)*linspace(0,1,nfft/2+1);
timefft = fft(X(:,2),nfft)/L;% frf of displacement
fre=2*abs(timefft(1:nfft/2+1));% frf of displacement
figure(1),plot(f,fre); grid on % fig A
% Natural frequencies without any scale adjustment
frf=fft(X(:,2));
figure(2),plot((abs(frf))); % fig B natural frequencies, fft, fourier transform MATLAB Answers — New Questions
How to get the planner task Progress using power automate?
I am trying to filter the planner tasks based on the Progress column:-
i tried those 3 actions, but none of them will return or allow us to filter based on the Progress column:
1) List all Tasks
2) Get Task Details
3) Get a Task
any advice?
Thanks
I am trying to filter the planner tasks based on the Progress column:- i tried those 3 actions, but none of them will return or allow us to filter based on the Progress column: 1) List all Tasks2) Get Task Details3) Get a Task any advice?Thanks Read More
Can’t find password to email address on my pc
I’m having trouble accessing my email account on my Windows 11 computer. I’ve forgotten my password and can’t seem to recover it. I’ve tried using the password recovery feature on the email provider’s website, but it’s not working for me. I’ve checked my PC’s settings and can’t find any information on where my email password might be stored. Now, I’m stuck and unable to access my email account.
I’m looking for advice on how to recover my email password or reset it if possible.
I’m having trouble accessing my email account on my Windows 11 computer. I’ve forgotten my password and can’t seem to recover it. I’ve tried using the password recovery feature on the email provider’s website, but it’s not working for me. I’ve checked my PC’s settings and can’t find any information on where my email password might be stored. Now, I’m stuck and unable to access my email account. I’m looking for advice on how to recover my email password or reset it if possible. Read More
Recent changes could not be saved. Refresh the page to undo the changes and continue working
Hello,
Over the past few days I have experienced challenges with the Project for the web part.
It consists of changes not saved in the project folder. Instead, this error message appears.
“Recent changes could not be saved. Refresh the page to undo the changes and continue working. Correlation ID: 6883f5fd-35f0-4bef-8423-8e5bf2dfd36f”
What does this mean and what must be done so that I can use Project for the web again?
Best regards,
Hello, Over the past few days I have experienced challenges with the Project for the web part.It consists of changes not saved in the project folder. Instead, this error message appears.”Recent changes could not be saved. Refresh the page to undo the changes and continue working. Correlation ID: 6883f5fd-35f0-4bef-8423-8e5bf2dfd36f” What does this mean and what must be done so that I can use Project for the web again? Best regards, Read More
matching excel row data to filename based on matching data left of underscore
Hoping somebody can help with what I believe can be done either using Power Query or VBA.
I have an Excel file that includes thousands of entries – each entry has an object number and SOME objects will have an associated file on the hard drive (or SharePoint / remote server). I would like the script to be able to review the data from the file name left of the first underscore to match with the object number and record the filename in the correct field “demo file path” in the attached sample file. E.g. object number 123 is related to file 123_has-extra_from_3733-AREA_RULE_Progress_Report_Feb._231955.pdf
I am OK if the system needs to place a message in the related entry that states “no match found”, it is a bonus but not required.
Hopefully with the sample data that includes a second tab of the file that are in the existing folder and the above details somebody can help out.
If the solution cannot read directly from a specific folder / site and needs a worksheet with all the file names, I can easily work with that solution.
Thank you.
Sample File Hoping somebody can help with what I believe can be done either using Power Query or VBA. I have an Excel file that includes thousands of entries – each entry has an object number and SOME objects will have an associated file on the hard drive (or SharePoint / remote server). I would like the script to be able to review the data from the file name left of the first underscore to match with the object number and record the filename in the correct field “demo file path” in the attached sample file. E.g. object number 123 is related to file 123_has-extra_from_3733-AREA_RULE_Progress_Report_Feb._231955.pdf I am OK if the system needs to place a message in the related entry that states “no match found”, it is a bonus but not required. Hopefully with the sample data that includes a second tab of the file that are in the existing folder and the above details somebody can help out. If the solution cannot read directly from a specific folder / site and needs a worksheet with all the file names, I can easily work with that solution. Thank you. Read More
How pricing works on Azure Stack HCI?
Hi Experts,
We are planning to use Azure Stack HCI, one of our questions is how the pricing works for SQL on a VM and SQL using PaaS on HCI?
In our understanding SQL on a VM requires: SQL license, OS license, compute and storage cost.
Paas SQL on HCI requires compute and storage cost.
is this correct and which one is the most cost effective and if can you expound why?
Thank you in advance.
Hi Experts, We are planning to use Azure Stack HCI, one of our questions is how the pricing works for SQL on a VM and SQL using PaaS on HCI?In our understanding SQL on a VM requires: SQL license, OS license, compute and storage cost.Paas SQL on HCI requires compute and storage cost. is this correct and which one is the most cost effective and if can you expound why? Thank you in advance. Read More
How can I mute and unmute yourself from Windows taskbar in Microsoft Teams?
Specifically, I’m trying to find a way to mute and unmute myself directly from the Windows taskbar. I’ve noticed that sometimes my audio is turned on and I’m accidentally broadcasting my background noise to the team. I’d like to be able to quickly mute and unmute myself without having to navigate through the Microsoft Teams app or desktop interface.
Does anyone know how to access the audio settings from the Windows taskbar, or if there’s a shortcut or hotkey that allows me to quickly mute and unmute myself in Microsoft Teams?
Specifically, I’m trying to find a way to mute and unmute myself directly from the Windows taskbar. I’ve noticed that sometimes my audio is turned on and I’m accidentally broadcasting my background noise to the team. I’d like to be able to quickly mute and unmute myself without having to navigate through the Microsoft Teams app or desktop interface.Does anyone know how to access the audio settings from the Windows taskbar, or if there’s a shortcut or hotkey that allows me to quickly mute and unmute myself in Microsoft Teams? Read More
Generating a list of Dates using nested array inside SEQUENCE function?
Hello,
I am trying to generate a list of dates with different intervals using an array inside of a single SEQUENCE function. How do I do this? Cell references are in bracket below and the results I’m looking for.
Ex:
Start Date End Date Day Interval
(A1) 2024-02-15 (B1) 2024-03-07 (C1) 7
(A2) 2024-02-23 (B2) 2024-03-22 (C2) 14
Looking to generate
2024-02-15
2024-02-22
2024-02-29
2024-03-07
2024-02-23
2024-03-08
2024-03-22
Basically it generates a list of values going through each start date in the array (A1:A2) and their respective interval (C1:C2). I am trying to use one instance of the SEQUENCE function to do this nesting arrays inside instead of using a SEQUENCE function for each start date. Any ideas? Thank you in advance.
Hello, I am trying to generate a list of dates with different intervals using an array inside of a single SEQUENCE function. How do I do this? Cell references are in bracket below and the results I’m looking for. Ex:Start Date End Date Day Interval(A1) 2024-02-15 (B1) 2024-03-07 (C1) 7(A2) 2024-02-23 (B2) 2024-03-22 (C2) 14 Looking to generate 2024-02-152024-02-222024-02-292024-03-072024-02-232024-03-082024-03-22 Basically it generates a list of values going through each start date in the array (A1:A2) and their respective interval (C1:C2). I am trying to use one instance of the SEQUENCE function to do this nesting arrays inside instead of using a SEQUENCE function for each start date. Any ideas? Thank you in advance. Read More