I’m using an Arduino Uno with Simulink and trying to read serial data using the Serial Receive block. The Arduino is printing voltage values from an analog sensor as follows:
int sensorValue = analogRead(A0);
float voltage = sensorValue * (5.0 / 1023.0);
Serial.println(voltage);
However, I’m facing a conflict because the Serial Receive block and External Mode are trying to use Serial Port 0, which is the only hardware serial port available on the Arduino Uno.
My Setup:
Hardware: Arduino Uno
Simulink Blocks:
Serial Receive block to capture the data sent from Arduino
Mode: I attempted to use both Connected I/O and External mode (Run on board), but as the simulation doesn’t allow to change the the serial port from 0 in either mode, nor can I change the pin number in the Serial Receive block.

Problem:
When I run the model, I receive the following errors:
Run with I/O
Caused by: Serial Port 0 used by the Serial Receive block, is also used for Connected I/O. Change the port number used by the block in your model.
Run on baord
Serial Port 0 used by the Serial Receive block is also used for External mode. Change the port number used by the block.
However, the Arduino Uno only has one hardware serial port, and there’s no option to change the serial port in the Serial Receive block or in the hardware setting in the Simulink.

How can I resolve this conflict and successfully read serial data from the Arduino Uno in Simulink?I’m using an Arduino Uno with Simulink and trying to read serial data using the Serial Receive block. The Arduino is printing voltage values from an analog sensor as follows:
int sensorValue = analogRead(A0);
float voltage = sensorValue * (5.0 / 1023.0);
Serial.println(voltage);
However, I’m facing a conflict because the Serial Receive block and External Mode are trying to use Serial Port 0, which is the only hardware serial port available on the Arduino Uno.
My Setup:
Hardware: Arduino Uno
Simulink Blocks:
Serial Receive block to capture the data sent from Arduino
Mode: I attempted to use both Connected I/O and External mode (Run on board), but as the simulation doesn’t allow to change the the serial port from 0 in either mode, nor can I change the pin number in the Serial Receive block.

Problem:
When I run the model, I receive the following errors:
Run with I/O
Caused by: Serial Port 0 used by the Serial Receive block, is also used for Connected I/O. Change the port number used by the block in your model.
Run on baord
Serial Port 0 used by the Serial Receive block is also used for External mode. Change the port number used by the block.
However, the Arduino Uno only has one hardware serial port, and there’s no option to change the serial port in the Serial Receive block or in the hardware setting in the Simulink.

How can I resolve this conflict and successfully read serial data from the Arduino Uno in Simulink? I’m using an Arduino Uno with Simulink and trying to read serial data using the Serial Receive block. The Arduino is printing voltage values from an analog sensor as follows:
int sensorValue = analogRead(A0);
float voltage = sensorValue * (5.0 / 1023.0);
Serial.println(voltage);
However, I’m facing a conflict because the Serial Receive block and External Mode are trying to use Serial Port 0, which is the only hardware serial port available on the Arduino Uno.
My Setup:
Hardware: Arduino Uno
Simulink Blocks:
Serial Receive block to capture the data sent from Arduino
Mode: I attempted to use both Connected I/O and External mode (Run on board), but as the simulation doesn’t allow to change the the serial port from 0 in either mode, nor can I change the pin number in the Serial Receive block.

Problem:
When I run the model, I receive the following errors:
Run with I/O
Caused by: Serial Port 0 used by the Serial Receive block, is also used for Connected I/O. Change the port number used by the block in your model.
Run on baord
Serial Port 0 used by the Serial Receive block is also used for External mode. Change the port number used by the block.
However, the Arduino Uno only has one hardware serial port, and there’s no option to change the serial port in the Serial Receive block or in the hardware setting in the Simulink.

How can I resolve this conflict and successfully read serial data from the Arduino Uno in Simulink? simulink, serial receiver, arduino MATLAB Answers — New Questions

​